EPDM is the abbreviation of Ethylene Propylene Diene Monomer. This material is used for roofing insulation. EPDM is a synthetic rubber, and the development of this material over the period has been dramatically improved. EPDM roofing is most commonly use for commercial buildings. In this article, you will learn about a descriptive overview of EPDM roofing installation in Michigan.
On the commercial building roof, firstly, an insulation board or EPS foam is placed; over these layers, EPDM roofing is installed for greater efficiency.
Reasons for EPDM roofing installation in Michigan
Many reasons are available for the EPDM roofing installation in Michigan. The most important reason for installing Business category EPDM roofing is the life span of this insulation rubber material, which is almost fifty years old. Other reasons for installing this roofing for your commercial or residential building are available. Let’s have a look at these reasons:
Strong and resilient
Because the EPDM material is made of rubber and some other strong substance, this roofing insulation is solid and resilient. The rubber material can be bent without any breakage. The resilience of EPDM material can also be determined by the temperature balance capacity of this material, which has a great range (from minus fifty-eight degrees centigrade to three hundred two degrees centigrade)
EPDM roofing in Michigan can comfortably protect from the heat of sunlight. The rubber material is an excellent insulator for heat and other weather conditions. So, outdoor awnings. EPDM roofing installation in Michigan is very beneficial for individuals.
Good for environment
EPDM roofing is perfect for the overall environment of Michigan. Because this material is made from used rubber tires, so, these use tires, instead of spreading pollution, are recycled and made into the roofing insulation material. The other environment-friendly characteristic of EPDM roofing is that after completing its lifespan, the rubber roofing can be again recycled and used for making new EPDM roofing.
The cost of EPDM roofing installation in Michigan is lower than any other type of roofing installation. The installation procedure of EPDM roofing is also straightforward and durable.
Low maintenance cost
The other benefit of EPDM roofing installation is that you have to spend very little money to maintain this roofing. Experts said that you could ideally ignore the maintenance of EPDM roofing.
Helps in saving energy
EPDM roofing installation is also helpful in saving energy costs. Because this material reflects the sunlight, a lot less energy is consumed for the cooling purpose of the building rooms.
The procedure of EPDM roofing installation in Michigan
The installation procedure of EPDM roofing is contained multiple steps. In the first step, the roof floor is prepared for the later procedure. In the roof preparation, the roof’s floor is cleaned from sand, oil, and grim after this installation of drip batten comes into play.
Drip batten is necessary for the drainage of rainwater. Once the dripping batter is installed, it’s time to install the drip edge on the curved top of the drip batten for proper guidance of roof water to the gutter system.
After this, actual EPDM roofing rubber material is installed on the complete roof; after installing EPDM roofing with the proper method, final touches are given. In this final touching adhesive material is applied to the roof’s edges.
EPDM roofing installation in Michigan is quite a good investment, which will pay you back in energy efficiency and saving. It also adds value to your property. A building with the EPDM roofing installed can be sold at higher prices.
- Is EPDM possible to install directly on plywood?
How can EPDM be installed on plywood? The EPDM rubber roofing can be installed on several surfaces, but it is most effective when applied to timber deckings such as plywood roofing grade or OSB sterling board.
- When should EPDM roofing overhang?
A single large sheet of EPDM will be provided when you order it. Work out the size of your roof before ordering. Add 300mm to the overall dimension by allowing a 150mm overhang on each edge. Take the slope of the roof into account as well.