Home Improvement

How to Install Laminate Wooden Flooring

If you’re thinking about installing a laminate wooden floor in your home, you may be wondering “How to Install laminate wooden flooring?” Here are some tips and tricks to ensure a proper installation. Calculate the square footage of your room and make an angled cut. Then, make sure to hide the perimeter gap. Afterward, apply an underlayment and apply glue to the bottom of the plank. This will protect your new Laminate Flooring in Dubai and make it look beautiful!

Calculate the square footage of the room

Before starting to install laminate wood flooring in a room, you must calculate its square footage. To do so, first determine the length of the room, followed by its width. Then, multiply the two measurements by the number of square feet. Ensure that you take measurements of irregular spaces and add them together to determine the total square footage of the room. If the room is square, you can use a tape measure with a slant to get an accurate measurement.

Measure the entire room to determine the proper square footage of the room before purchasing flooring. If the rooms are connected by walls, the process is similar to that of measuring a single room. But, if the rooms are not connected by walls, the calculation is slightly more complex. In such cases, you can divide the rooms into small, square or rectangular areas and then combine the measurements to arrive at the total square footage of the room. Don’t forget to include closets when measuring rooms.

Make an angled cut

The first step in making an angled cut when installing laminate wooden flooring is to locate the slanted wall. Once you have located the wall, you can use a bevel tool to measure the angle. Then, you can fasten the wing-nut and copy the angle onto the excess wood. After that, you can use a jigsaw to cut the angle. You can stagger the boards by cutting them at different lengths. The last board on the angled wall must be narrower and sawed out.

Once you have located the angled wall, you can now measure the width of the first and last boards. Measure the width of the room, then subtract half an inch for spacers. Make sure the tongue isn’t included in the measurements. Start at the top edge of the first board. If the angled cut isn’t perfect, remeasure. Otherwise, you may find that the installation is too wide or you have to use more than one board.

Hide the perimeter gap

The expansion gap is a vital feature when installing laminate flooring. The expansion gap in the flooring is what allows the floor to expand and contract with changes in temperature and humidity. Without the expansion gap, your new floor will expand and contract unevenly and will cause buckling. This can also damage the click system. The expansion gap in laminate wooden flooring is usually about 1/2 inch (12.5 mm) in width. Fortunately, there are many ways to hide this gap.

The expansion gap is the space where the floor meets fixed objects, such as walls and door frames. The expansion gap should be at least 9.5mm wide, though larger gaps are recommended in areas where there are extreme weather conditions. It is best to leave a gap of around 12mm, as this will allow the floor to expand and contract slightly with changes in temperature and humidity. The expansion gap is normally concealed by skirting boards and is not visible when you install laminate wooden flooring.


Underlayment is often a necessary part of flooring installation. You can install laminate straight over hardwood, or use underlayment if your subfloor is made of concrete or brick. In either case, you’ll want to choose a quality product that offers some underlayment, as it provides added padding and softens the laminate surface. While wood subflooring provides enough elasticity, concrete and brick require additional underlayment to provide a firm surface.

When installing laminate flooring, you should apply an underlayment that is two to three inches thick. If you install a thin layer of underlayment, you will have a solid base for your new flooring. Putting a second layer of underlayment underneath will only cause problems in the installation process. A foam barrier will provide additional moisture proofing and noise cancellation, but a vinyl-backed underlayment is an excellent choice for these purposes. Cork underlayment, on the other hand, is the most expensive and is mainly for noise reduction.

Using a laminate flooring cutter

Using a laminate flooring cutter

A laminate flooring cutter is a tool used for cutting a piece of wooden or plastic plank. These tools can be either circular or miter saws. While most blades cut on an upstroke, it is important to cut the laminate with the finish side down to minimize splintering. You can also use a Dremel tool. While these tools are portable, you need to be careful because sawdust can scratch your finished laminate flooring.

Using a laminate flooring cutter requires less time than using a reciprocating saw. This tool is ideal for cutting smaller pieces of laminate but is not appropriate for ripping large sheets of wooden plank flooring. Moreover, reciprocating saws require the blade to bite into the material before cutting. They also may damage the laminate’s finish if they cut it on an angle. However, if you prefer to use a reciprocating saw, you can use it to make shortcuts.

Cutting planks

In order to install laminate wooden flooring, you should first begin against the longest wall in the room. Depending on the size of the room, you may need to parallel the installation of planks in some areas. In these cases, you should place planks with the tongue side of the tongue facing out toward the wall. Place the next plank in the groove. Continue doing this process until the length of the first row is complete. Once you’ve installed all of the planks in a row, you should cut the last piece so it will fit into the space.

While most manufacturers recommend using a jigsaw or table saw to cut planks, some prefer cutting the tongue edges of planks facing the walls. In this case, you should use a fine-toothed saw to minimize the chance of splintering. Then, using a pull bar or tapping block, join the first and last planks in a row. If the first plank is too long, you can also snap it into place or score it if it’s too short.

Apart from that if you want to know about Rubber Gym Flooring then visit our Home Improvement category.

Related Articles

Back to top button